-
Before using your
vaporizer for the first time, it is important to leave it on for at
least 10 minutes without any herbs in the vaporizer. The clear glass
dome must not be inserted. So that the grime disperses into the air.
Do not inhale this vapor as it is simply a bit of grime generated
during the manufacturing process. Wipe of any of the residue with a
cloth.
-
Do not touch the heat
element as it gets extremely hot!
-
Home
Method of Vaporization -
Insert the clear plastic tube into
the small hole on the underside of the rubber collar of the yellow
vaporizer. Feed the 110 volt connection or 220 volt connection of
the vaporizer through the small opening at the top of the coloured
glass base. Feed the clear plastic tube into the hole on the side of
the glass base. Then push the vaporizer rubber mould into the
opening on top of the coloured glass base, so the vaporizer fits
firmly in the coloured glass base. Make sure that the hotplate is
pushed all the way down.
Place the chopped herb into the metal cup.
Then push the
clear glass dome into the black rubber vaporizer mould.
Then plug the vaporizer into the wall
(Outside of the USA or UK you will need a
plug adapter). Switch on the power point, then turn the
adjustable temperature control switch on your vaporizer until you
feel the vaporizer click on. The vaporizer takes approximately 9
minutes to reach the maximum temperature. As soon as the herb
starts to vaporize it is important to begin inhaling. To avoid the
vapor condensing on the clear glass dome. Vaporization takes
approximately 10 minutes once the desired temperature has been
reached. At this point the herb has had all the goodness extracted.
The herb should look a light to dark brown colour.
-
How
to turn the vaporizer on and adjust the vaporization temperature
- You turn on the vaporizer by
turning the black nob in a clock wise direction. You will feel a
slight click when the vaporizer turns on. You will also see a red
light come on at the top of the yellow shaft, just under the rubber
mould. Turn the knob as far as you can clockwise, until you can not
turn the knob any more. At this point the vaporizer is set at its
highest temperature. Approximately 300 degrees Celsius. To decrease
the temperature turn the knob anti clockwise. To set the minimum
vaporization temperature turn the knob anti clockwise, as far as you
can without turning the vaporizer off. At this point the vaporizer
is at minimum temperature approx 110 degrees celcius. You will feel
a slight click if you happen to turn the knob to much and then red
light will go off. This indicates that the vaporizer has been
switched off. As you turn the vaporizer from minimum to maximum you
will see the red light on the vaporizer become brighter.
-
How
to look after your vaporizer and get the most out of your herbs
- Cut your herb up so it is quite
fine. Place evenly over the hot plate. Set the vaporizer to the
desired temperature. Look out for a fine mist which occurs when it
is time to vaporize. It is easier to see the mist if a lite is shone
onto the clear glass dome and you are in a dark room. When you have
had enough reduce the temperature to the lowest temperature. This
will allow you to clear the chamber and catch your breath. Then set
the vaporizer back to the desired vaporization temperature. Then
wait until the vapor becomes thick within the chamber. Repeat this
process as many times as necessary. When there is no vapor left
within the herb switch the vaporizer of by turning the knob
anticlockwise until you feel a click and the red light turns off.
Then turn off the power at the power point or in the car. Do not
leave the vaporizer on if it is not in use. If you look after
your vaporizer, it should work for many years.
-
Cleaning Remove
the glass dome and simply blow off the waste substances.
You can clean the clear glass dome with CLR or dishwashing
detergent. Please make sure that you rinse the dome thoroughly with
water to remove any residue. Then dry any remaining liquid from the
dome.
